Do you know the five most common signs that you need to do log home stain maintenance?
Identifying signs that it’s time to maintain your log home with a fresh coat of stain, or Cascade® Clear Coat is easy. Start by downloading this handy inspection guide to carry along with you as you perform your inspection as the very first step in your maintenance plan.
Loss of sheen
Most clear coats have a satin sheen when first applied, and while still in good shape. Over time, that clear coat or stain erodes due to weathering. Look at your home in the sun or take a flash light to it. If it looks a bit flat, it’s time for maintenance.
Color shifts in log Stain
Does your stain look darker than it did originally? Perhaps there’s some fading going on where it’s exposed to sun? Both are signs that your stain (and the UV filters in it) have worn off and need to be replenished.
Water not shedding
Break out the hose or a spray bottle. Is water still running down the logs? It should sheet off the wood, not bead up. Any areas where water isn’t “sheeting” well needs a fresh coat of stain or clear coat.
Dirt, pollen, bird poo, etc.
Over time, surface contaminants will eat away at the integrity of your stain. If you can see these contaminants, it’s time for a good wash down at least, and possibly time for more another coat of stain.
New micro checks and cracks in the wood
Have any new micro checks (the tiny cracks in the face of the logs themselves) appeared? If so, those are unprotected by stain and need to be treated! Left unprotected, they’ll allow moisture to come in that can compromise the integrity of the stain, not to mention invite rot. Make sure new micro checks are filled with stain or a your clear coat. (Important note: Make sure any crack that’s 1/4″ wide or larger on the upper curve of the log is caulked with Conceal® or Log Builder®, not just stained.)
We have GREAT news! It’s only necessary to apply more stain and/or a clear coat where it’s needed, when it’s needed.
In some cases, the north and east sides of the home can be skipped the first time you maintain the south and west sides. They don’t get the same UV exposure and don’t tend to need care as soon. Any areas protected by an eave, overhang, or porch will likely require less maintenance over time, too. Proper planning and education will help you stay on top of your maintenance, so many times there’s no need to re-coat the whole darn house every time. (We’re all about saving the weekends for fun and relaxation, too.)
That’s it! Great job! You’ve determined what needs to be done to protect your log home come spring.
Need a little more guidance and help planning? No problem, our customer service team is always happy to help! Give us a call at 800-767-5656.
We devote a lot of time sharing what to do to make your business more successful. This month, we’re sharing four things smart business owners should avoid doing!
It seems insignificant, but some sort of bond breaker — backer rod or grip strip or clear packing tape — is the difference between a long-lasting, durable caulking and chinking job and redoing the work year after year. That bond breaker creates the ideal joint design to keep your caulking and chinking stretching properly over time.
Backer Rod, Grip Strip, and Log Gap Cap all help you create the ideal joint design for a long-lasting, durable seal. Follow these simple steps or learn more, https://www.youtube.com/c/Sashco.
Keeping your log home beautiful and protected is a big deal. You’ve invested too much to skimp when it comes to stain maintenance. Consistent maintenance inspections and routine reapplication of stain or clear coats where needed, when needed, are the key to keeping your dream log home, well, dreamy.
That said, how many times have you thought, “I should really get this project done around the house,” and then put it off another year?
We won’t require you to answer (because then we’d have to admit the same thing ourselves…eek!)
Have you ever tried to run a cloth or duster over wood with no clear coat on it? It’s horrible! It catches on the wood, doesn’t remove the dust, and ultimately makes a bigger mess. Even worse is trying to clean wood that is permanently yellow from UV exposure and oxidization. Follow these 3 steps to create an easy-to-clean, won’t-get-discolored constant warm glow in your log or wood home. BONUS: Interior finishing needs to be done only once. Routine cleaning — wiping down cobwebs, dust that settles, fingerprints, etc. — is all that’s needed to maintain the finish and keep the wood looking like new.
Outdoor hand rails and spindles, especially those not protected by overhangs, require specialized and more frequent care because of their extreme exposure to weather. A few easy tips are all it take to to prevent rot on log railings.
So, you did a stellar job of sealing cracks and checks in your log home. Hooray! Now, a couple of years later, you’re noticing that some of the caulk has cracked. After all that hard work? Ugh. So, what do you need to do to fix cracked caulk? Keep reading for all the details.
Why does caulk crack anyhow?
On most log homes, a handful of those logs will undergo extreme movement. This movement is a part of what makes a log a log. Moderate movement is normal, but the occasional maverick log can randomly and unpredictably twist, shrink or warp in response to moisture changes (like the first time the heat is turned on that winter), moving more than any sealant can possibly handle. When this extreme movement occurs, it will cause the sealant to fail either cohesively or adhesively. Here’s how to do repairs.
Cohesive failure
This is where the sealant splits apart down the middle of the joint. There’s still caulk sticking to the sides of the joint. Repairing cohesive failure is pretty simple:
Relieve the pressure by taking a razor blade to finish the job. (Sounds silly, but this is necessary for the repair to work properly.)
Insert backer rd behind the caulk, if there isn’t some there already.
Clean the surfaces to remove dust and other surface contaminants.
Apply more sealant right over top. You can only do this if the product you’re using is compatible with whatever’s already in there. With Sashco’s products, this is no problem. If you used silicone, you’ll have to remove it all. Boo.(Moral of the story: don’t use silicone on log homes.
Adhesive failure
This is when the sealant pulls away from the edge of the logs. In this case, a bit more investigation is necessary. Adhesive failure can be either due to movement or because of an incompatibility between the stain or clear coat used on the logs and the caulking. If it’s only due to movement, here’s the fix:
Remove the sealant completely. You’ll have to cut it out entirely.
Insert backer rod or another bond breaker behind the caulk or chinking, if one is not already there.
Clean the joint, especially at the edges where the new product will be sticking. Make sure there are no loose wood fibers or peeling stains or paints. It may mean you need to break out the sand paper or Dremel® tool. (Power tools. Argh.)
Apply more caulking or chinking over top. Smooth it out, just like before.
If the failure is due to an incompatibility between the stain/clear coat on the wood, you’ll have to do some more extensive work to get the new caulking or chinking to stick:
Remove what’s in there now.
Sand down the edges of the joints to remove the stain/clear coat.
Clean with a degreaser of some kind (Formula 409® and the like do a good job).
OPTIONAL (and best): Stain just those areas with a compatible product.
Insert backer rod or a bond breaker, if one isn’t already there.
Apply more caulking and chinking, smoothing as before.
Looking for tips on log home care and maintenance? Check out our blog for more tips and information that will help you preserve your dream log home.
Log Blog
Explore inspiration, learn about our products and get tips from the pros over at the Log Blog!
What do you get when you combine a roofing contractor and a sealant manufacturer for a chimney repair project (apart from much time spent arguing over who gets to use the rad tools)? An expert example of tuckpointing a chimney.
Recently, Sashco president Les Burch and Sashco team members Sabrina and Randy helped Shane Guerra, the owner of Synergy Property Solutions, and his team, repair a chimney. Shane used Mor-Flexx, a latex acrylic caulk designed specifically for the chimney repairs. Mor-Flexx is ideal for use on mortar between stucco, concrete, bricks, and stone, or stucco repairs.
Don’t compromise at the end of a long and arduous journey by using an inferior stain not designed for logs. Capture and Cascade deliver performance worthy of the journey that got you here.
Moves with your logs and timbers
Won't hide the wood grain
Easy clear coat maintenance with Cascade(R) exterior clear coat
Backer Materials that Seal Things Right the First Time Backer Rod, Grip Strip, and Log Gap Cap all help you create the ideal joint desing for a long-lasting, durable seal
Logs are in constant dynamic motion. That's why there's Log Builder®, the sealant made for log structures. Stretches up to 500% of original size, while still maintaining tenacious adhesion to the wood.
When other chinking pulls away, Log Jam holds its seal With Log Jam chinking, you can keep the cozy feel and rustic look of a log home without compromising comfort and performance.
Easy to Use - Hard to See Keep out weather, bugs, and moisture without seeing it. Conceal disappears into the woodwork so you don't know the wood starts and the caulk begins.
It's Music to the Eyes Symphony works in harmony with the unique character of your logs and wood to reflect an atmosphere or cozy warmth and elegance while creating and scuff-resistant and durable surface that's easy to dust.
Right Color. Right Quantity. Right Now. Never run out of stain at the jobsite again. Stock exactly what you need in your truck or trailer at the jobsite.
Easy to mix
The same color, durability, and application you've come to expect from Capture Log Stain and Transformation Log & Timber
Maintenance Made Easy Now that Capture® Log Stain is applied, it’s time for Cascade® Clear Topcoat to bring out the depth and character of your unique woodgrain while protecting it against moisture, mildew, and algae. Predictable and affordable routine maintenance with Cascade throughout the years means your home stays protected and beautiful. Easy!
Keep the Color the Color Colorfast delivers the ideal canvas for stain application and leaves behind the strong foundation necessary for long-lasting color. It’s color confidence for your log home.
Rot, weather, insects, fungi all pose a serious threat to your logs. Protect your investment—treat your logs first to make them last. Tim-bor® helps protect your home from the costly damage caused by rot and insect infestation.
Bugs don't stand a chance
Easy to mix and apply
Prevents decay fungi
Costs 5 times less than glycol-based borate products
Remove Wood Felting and Raised Grain Remove wood fuzz (called felting) after power washing or media blasting, and knock down excessive raised grain with Sashco's finish sanding tools
Clean and brighten bare logs and wood, remove surface dirt, pollen, and kill mold for maintenance, and keep your logs looking fresh with CPR Log Cleaner and Brightener
